XW-G1
107 files
-
G1 Drawbar Pack
By BrettM
After experimenting with the nona-layer method I posted in the G1 area a while back, I now realise there is an easier way to create a complete drawbar organ on the G1: save the nine basic drawbar tones as splits across two user waves. Each split corresponds to one drawbar. Then all you have to do is edit the volume of each split to create the desired registration. Don't forget to change the volumes in increments of 16 if you want true drawbar authenticity, although finer adjustments are possible. The splits are constructed as follows:
File/Split Note played Drawbar
DBL88888 Split 1 C3 16'
DBL88888 Split 2 G4 5 1/3'
DBL88888 Split 3 C4 8'
DBL88888 Split 4 C5 4'
DBL88888 Split 5 G5 2 2/3'
DBH8888 Split 1 C6 2'
DBH8888 Split 2 E6 1 3/5'
DBH8888 Split 3 G6 1 1/3'
DBH8888 Split 4 C7 1'
Also included in the pack is a performance which ties it all together, including the 2nd and 3rd percussion in zones 3 and 4. Knob 1 adjusts the volume of zone 3 and thus switches 2nd percussion on or off and increases it's volume in the mix. Ditto for knob 2 and 3rd percussion. Knob 3 controls the overdrive gain of the rotary speaker and knob 4 controls its speed.
It uses up two user waves, but this is a small price to pay for a fully functional drawbar organ. Save the files to a card until needed.
The main limitation of this set up is that it chews up the polyphony pretty fast because we're mixing the drawbar sound in real time. One note on the keyboard activates 11 tones. A triad uses 33! If this causes a problem, just record a single note, say C4, in the sampler and you're back in business. This is also a good way to store specific registrations that you may want to reuse. Enjoy!
=== Version 2.0 ===
I noticed some distortion when playing triads in version 1.0 of the organ, which I put down to exceeding the polyphony, but now realise that it was just straight out clipping. So version 2.0 has the same files with the volumes of each split reduced from 127 to 80. This should eliminate any distortion and also makes it easier to create standard registrations using stop increments of 10 rather than 16, you may have to turn up the volume a bit more however. When some of the drawbars (splits) are "pushed in" (turned down), it may be possible to increase the volumes of the others without experiencing clipping.
=== Version 3.0 ===
I have since realised that the pitch shifter can shift up two octaves, but can shift down many more, so I've raised everything by an octave. Thus all the notes in the table above are an octave higher. This allows the organ to play from C7 down which makes it much more playable. Previously the notes repeated after C6. I've also improved the looping in the splits.
320 downloads
(0 reviews)0 comments
Updated
-
LIVE JAM FX.ZPF
EDM Live Jam FX with Performance Multi-function Keys
Performance Name: LIVE JAM FX
This performance uses multi-function keys to change the tone/patch being played in Zone1/Part 1 from C- to C6. The multi-function keys section is from C#6 to C7. The black key multi-function keys are control keys that turn DSP effects on/off for Zone1/Part 1, change the tone to play on Zone1, and change the DSP effect being used. The white multi-function keys section quickly sets the DSP effect to a preset effect.
Link to picture with more info:
http://www.facebook.com/photo.php?fbid=257944387710927&set=a.257944371044262.1073741836.100004861031136&type=3&theater
72 downloads
- Performance
- FX
- (and 4 more)
(0 reviews)0 comments
Submitted
-
Jazz fusion and all of my work in progress ZSS
By XW-Addict
Jazz Fusion performance patch I fooled around with to program the XW and unfinished unamed duplicated StepSeq I made during the time.
122 downloads
(0 reviews)0 comments
Submitted
-
(0 reviews)
0 comments
Submitted
-
(0 reviews)
0 comments
Submitted
-
(0 reviews)
0 comments
Submitted
-
(0 reviews)
0 comments
Submitted
-
Quick Organ
By BrettM
While working on version 3.0 of the G1 Drawbar Pak, I started thinking about making an organ that just uses up one user wave slot rather than two. This is it. The problem is: how best to arrange nine sine waves over five splits.I tried a few combinations but this one turned out to be the most useful.
Split 1: 16', 5 1/3' and 8' drawbars fully out
Split 2: 4', 2 2/3' and 2' drawbars fully out
Split 3: 1 2/5' drawbar
Split 4: 1 1/3' drawbar
Split 5: 1' drawbar
I think many of the classic registrations are possible with this arrangement. E.g., the bread and butter tone of 888000000 is produced by just having the volume up on spit 1.Each of the high frequency "brilliance" drawbars has a dedicated split and is thus easy to adjust.
It is also worth remembering that each split has its own filter, which can be useful for generating more options in splits 1 and 2; and is especially useful for tweaking the mid tones in split 2.
I have not tried to implement percussion but it can be fairly easily added by combining this tone with the performance in the G1 Drawbar Pak.
=== Version 2.0 ===
I've tried to improve the looping.
97 downloads
(0 reviews)0 comments
Updated
-
(0 reviews)
0 comments
Submitted
-
(0 reviews)
0 comments
Submitted
-
LastOrder
By XW-Addict
Progressive Rock kind of thing feel free to improve .
Here how it sounds.
https://soundcloud.com/clay-louis-petty/lastorder-dt
72 downloads
(0 reviews)0 comments
Updated
-
RainbowDubStep
By XW-Addict
Choco variant of dubstep. Preferred tempo 130 / 165 / 180
Here is how it sound.
https://soundcloud.com/clay-louis-petty/dubstep-city-dub2stepchoco
75 downloads
(0 reviews)0 comments
Submitted
-
Synthesizer bees (Solo Synth)
By Gnomo Alegre
Flight of bees.
DSP: Auto pan.
OSC 1: CZ-Wave 29
OSC 2: Reverse Saw
OSC 3: #CZ-Wave 18
OSC 4: Sy_SH Pulse 1
OSC 5: White Noise (not brown noise)
127 downloads
(0 reviews)0 comments
Submitted
-
StellarGroove
By XW-Addict
Though to add this one from the Interstellar package thing I'm working on.
Just from this Sseq I could derive lots of different rhythms.
Tip : Turn off with the mixer the bass, sol1, sol2, chrd to keep the
drum beat, change the drum patterns to a whole new drum beat.
Get and be inspired I've already got lots of other Sseq derived from only
this Sseq.
72 downloads
(0 reviews)0 comments
Submitted
-
BizzarePad
By XW-Addict
This is the performance patch and step sequence I've did the cool and awesome motion with,
Use the Knobs to change how it sounds. The coolest thing is to create you're own phrase and then let
the arpeggio go at it.
Also use the the step buttons to go into sync with a step sequence and the Octave keys to go lower
in the key register -2 is the max to keep some sense in the sound.
*this still under construction as part of Interstellar package.*
183 downloads
(0 reviews)0 comments
Updated
-
Interstellar patches and drumset
By XW-Addict
Before installing don't forget to store you're own patches in user space .
Thank you for downloading Its not finished yet and this package not in order meaning some file needs more tweaks but I guess better now then 2later to upload .. Missing are Phrases , Arpeggio's and linking performance to step sequences but experiment along and something will come up if you mix them a bit.
Some patches have buttons assigned use them to get a nice blend of sonic,
Some patches have arpeggio .
Some patches Solely build for use with looper.
Some patches experimental XD like hey gotta try something news once a while.
Some patches may be terrible that way but fun in the other.
Some patches and stepsequence are still under construction.
What I'm missing is using the solo-synth within performance patches I've discovered
It would make a bigger difference which will be the next thing some.
Enjoy.
172 downloads
-
Chirps FX
By XW-Addict
Sampled Instrument FILE.
Load into sample player then go to Tone User bank 200 and select the bank where the file is loaded in.
Experimented with reverse recording with the sampler and edited with external recorder by recording the sound into it and slowed down the speed then using the XW-G1 editor to make the patch all done with experimenting.
What I've done is recorded a step sequence called ReverseForwrd (available for download from interstellar pakage) and recorded it as a reverse loop then I recorded that back into the roland micro br80 and played it back by slowing the playback speed to 25% this is different on the micro br80 because you retain the same fidelty as you would with normal speed but now slower which gives a different sonic Fx.
I liked it so much that I recorded it back into my computer chopped the good bits out and imported them as multiple waves into the XW-G1 editor and made this patch out of it one word.
AWESOME.
72 downloads
(0 reviews)0 comments
Updated
-
GrooveBox 1.ZSS
NOTE: The website would not let me upload the step sequence with the correct extention of .ZSS, I had to change it to .ZSQ to upload it. So if you download it you will have to change the file extention from .ZSQ back to .ZSS the correct file name extention.
Description:
This is the StepSequence with a new user configuration called GrooveBox 1.
I had an issue using the XW-G1 factory settings for the StepSequencer as a groovebox. The issue is I want to use the sliders to turn the parts on & off with all drum parts and the bass guitar part on the same group of sliders. The factory setting has the kick drum on slider 8 in the first set of sliders (1-8 sliders) and the other drum parts on 9-12 sliders and the bass guitar on part 13.
So I created a new user step sequence configuration with the parts moved around a little. I moved the kick drum from slider 8 (part 8) to slider 13 (part 13), the bass guitar from slider 13 (part 13) to slider 14 (part 14), and solo 1 from slider 14 (part 14) to slider 8 (part 8). I could not change the part names. The part 8 is still named "Drm1" even though it is now "Sol1", part 13 is still "Bass" even though it is now "Drm1", and part 14 is still named "Sol1" even though it is now "Bass".
Instructions for use:
1. Press the "STEP SEQUENCER" button
2. Press the "SELECT" button to select sliders 9-16
3. Create a sequence by turning the buttons off & on for the parts 9-16 as usual
4. While playing the sequence, Press the "MIXER" button to bring up the mixer menu and make sure "Part" is selected so the sliders turn on & off the parts. Slider up turns on the part & slider down turns off the part
70 downloads
(0 reviews)0 comments
Submitted
-
Sitar Groove
By XW-Addict
Install to a Free User Slot.
Don't forget if needed to let the Performance know where Arpeggio, Step sequence and DSP.
This can be done in edit mode sequencing etc same also for the sample loop.
Set the Bpm to 138 this is to sync with the sample loop.
Zipped the step-sequence and DSP for reasons known.
I've set the knobs to Cutoff , Attack , Release, Decay
My settings are:
Due to my peculiar sound design skills you may need to
transpose the keyboard to -03 Holding Transpose and press minus button.
Cutoff 110
Attack 50
Release 110
Decay 50
One more interesting performance thing if you've set it up right press Hold Arpeggio,
Select with the Minus step button this will change the which sync type you want during
performance this can be handy to set up front.
I've set it up on S/Sq so that when I hold a key the Arpeggio and step sequence play at once
and when the key is released it stop playing by switching arp on and off during performance play
its awesome. Plus by switching the sync to on only it switches the S/seq off leaving room to turn on
the sample looper and have a go with the pre-recorded performance to play along with.
Enjoy.
255 downloads
-
XW-G1 45 Performance Sound Sets
By XW-Addict
Sounds created to record and play with the Looper, They are also new sounds for the G1.
This will get gradually filled up with more Performance sounds I've intentionally created to record
loops with the looper but as I've later discovered the standard step sequence are great joy also
for these patches. Hope you'll like some of them and be free to edit and make you're own from these.
4,703 downloads
-
Oscillator Shaping - RavingPundit
By XW-Addict
This is an example for using Oscillator Shaping on the XW.
Install it on a free user slot, assign solo-synth to zone 1 and
don't forget to add the custom arpeggio also in a free slot.
Its a rave synth btw :-) very addictive to play with.
RavingPundit.MP3
212 downloads
-
Queens solo-synth Break Free.
By XW-Addict
First attempt to create synth sound from "Queens Break-Free"
Queen allegedly used Oberheim OB synth to create this,
The G1 has Oberheim samples for both the synth and PCM parts
within the solo-synth.
For the synth part its 0087 - 0101
For the PCM part its 1767 - 1781
I've tried to figure out how to make that rich fat sound but I can't
identify it yet. However I've found using sample 0046 MG Square L
for synth part a better option to come close at it.
So I'm guessing its a square wave and now have to figure out how
to fatten it up and to make the sound glide down. maybe using portamento
but a single stroke from the last note going down a few octaves also work.
(work in progress)
146 downloads
-
Sound Addiction Sample Looper Set - WIP
By XW-Addict
Hello I've uploaded a sample looper performance set I've been working on off and on.
I've build sounds what I like or for certain music projects its a work in progress (WIP)
Some of the performances need the knobs to create a sound scape.
Some performances need octave shift or octave transition shift.
Some performances are just not finished some are.
Most performances have no category yet nor or are ordered in that form.
Some performance may sound lame while others have something interesting.
Some step sequence are harsh while others miss a certain kit some are just cool.
I'm always building music in the sampler so you might want to check what I've
left there first be warned I used headphones mostly so it might sound different
on the speaker. Also the kind of music I do is a bit fruity and weird so be warned
Everything is a bit sloppy but I'm one to take the moment of creation and go at it.
This ZAL file will erase most of you're own performances so be sure to backup your own
files first before installing this one.
SampleLOoperRules.
215 downloads