Oh_Man

Thank you all for the input, I was clearly too slow on the draw and someone else snagged it. It looked a little rough for wear with the corners kinda looking banged up / paint removed so perhaps used a little harder than not. Anyway kinda immaterial now but good knowledge to have if another should come up in my area.

WK's...I notice it's the same on all of them. I have [selling a 225] and a 6500. O

Privia - PX-5S

Hello, Looking at one in my area that looks to be owned by a gigging musician. Curious how the keys and their hammer action mechanics would be holding up? Do they suffer the semi 'clackiness' of other Casio boards? And reading a review on SoundOnSound they said it's "bouncy for one with such a short front‑to‑back scale". What does short front to back scale mean...shorter keys? Any issues I should be looking for or asking the seller about? O

Hello ... 1. I cannot seem to figure what Navi. Ch is for [default is 4]? 2. I'd like to split the board to play 2 separate plugins - is that done in the DAW? Thanks, O

I have a similar issue - it's plastic against plastic and 'most' of the sound seems to occur when the keys snap back up. Having taken these apart is seems to the the triple layering of the key assemblies and other spots where plastic hits plastic. Couple options - the board is reasonably disassembled so that's first. One I've done and the other about to try. Lubrication - to lube the keys with silicone. Don't buy the blue stuff it's corrosive to plastic but the orange stuff for brakes works or Synthetic Grease which is thicker. That said I think the brake stuff is better but more expensive. Option 2 [multiple] - There's a lack of screws holding down the keys - there's holes drilled for more screws so one option to make the assembly more stable with additional screws. Cloth tape used for wire / stereo harnessing OR I'm about to use hockey tape which is 'clothy' and just as thin. I'm about to put this in between the key assemblies and anywhere else the plastic is striking plastic to operate as a pad. There's a thread on this forum - search clack keys but it's for a different model but essentially talks about using cloth tape.

I would say take it apart which is fairly easy, more a pain due to all the screws, but you'll want to see what's going on in there. Might need some contact cleaner or something but you won't know until you've got it apart. If you have a cat then the contacts might have gotten hair on them [just a thought]. The 2 main bodies separate easily, the wires are long enough to all you to pull them apart. While you're in there put some silicone grease on the inside of the keys to reduce some of the clackiness and will simultaneously offer a little more resistance when playing them.

Call Casio service - I'm about to have the mic knob sent to me.

Hello ... On my 6500 the 60's EP and even the Dyno EP both have a sort of Fender Rhodes bark. Is that right? I got this second hand and did what I thought was a reset so making sure that's correct. That said it's not overly consistent, sometimes playing faster or hitting triads gets it going ... is there a way to increase, decrease or make it more consistent? Orion

Hi Brad, First...thanks for reaching out. Thanks for the headphone suggestion - yes that worked and got me doing another round of testing. It all works. I must be losing my mind as I get older, that or my ears are going to heck or maybe it was just late in the night. I did make sure this morning that those plugs were in there good so maybe something is up there but it's good and I feel like a twit. That said, the sound is quite low coming out of those outputs - ran it to my stereo system which has pretty respectable sound and had to turn it up more than thought. Does that sound right? Like is the impedance on those outputs quite high? For the record the 225 is louder in the same set up. O

Hello ... Ok picked up the 6500...deal was too good to pass up and love all the sound controls. First question and I'm sure they'll be more. I have a 1/4" Left/Right cable with a 3.5 mm adapter on the other end to run sound to some computer speakers - in this case. Got the 6500 plugged in and getting nothing going to the speakers. I know the cable is good, used it with a Lowrey when I had it and it's essentially new. Not impossible it doesn't work but highly unlikely. My 225 has a single out and so I just use a 1/4" to 3.5 mm adapter to the same speakers, no problem. On that note I tried the same set up to the Mono on the 6500 ... still no sound. Does the 6500 not dig computer speakers, or did I just buy a board with hooped outputs making it not so good a deal after all? O

Could you please offer the usage of this software?

@Chandler Holloway Ok thank you...good to know and thanks for the additional context. Yes it appears they took the sampling functionality out? Odd as that would allow 'some' ability to extend the tones, ie; record some virtual via the MIC and done. I've never tested it with my WK 225 but that's how I understand it works. That said, via an online demo the 6500's DSP tones are pretty extensive especially considering the configuration ability so not a big deal for me. Sounded pretty damn good to me though shame they only offer 10 user tones vs the 7600's 100 user tones. Also, regarding SoundFonts/Wav/etc - that are all over the place, is there anyway to do converts to this AHL? I've searched that but haven't found anything yet or if there's a different method? And am I missing something but it seems the CTK 900/WK 3200 offered greater drawbar type functionality vs the 6500 or is it just factored into the 6500's DSP Tone editing/manipulation they offer? Seems confusing. Thanks... Orion

Hello, It seems Casio for at least a little while allowed/gave extension functionality to their Tones. Came across the below link which is not for the 6500 but curious if this would work or there's something else available for the 6500? A 6500 has come up in my area and considering buying it and this would be excellent! It really seems that Casio pulled out all the stops with the CTK-900/WK-3200 - from it's extended Drawbar functions to this... https://music.casio.com/e/ https://music.casio.com/e/data_ex4/ Did the same for the CTK- 671 https://music.casio.com/e/data_ex2/ O

Hello ... I'd be curious to know what you ended up doing, if there was a workable solution, especially as I'm considering picking up a 6500 which is for sale in my locale. Might not be the greatest solution but there's a solid VST called iSpinner. https://www.kvraudio.com/product/ispinner-by-iliadis-instruments Download link: http://www.vstplanet.com/VST_effects/Modulation/iSPINNER.zip O